Montigo PVHIN58-300 Manual de usuario

Canadian Heating Products Inc. Langley, BC V4W 4A1 | Montigo Del Ray Corp. Ferndale, WA 98248If the information in these instructions is not fo

PVHIN58-300 with TMHIN58-40Page 10XG0521 - 111214How to use Diluter CollarThe PVHIN58-300 is equipped with a built-in diluter collar to allow air to b

ServicePage 11XG0519 - 070714CPower Vent WiringBLUEBROWNBLACKWHITEBLACKGREEN6 PIN MOLEXCONNECTORKEY WAYPVHFL58-300 & PVHFL510-300 Horizontal Power

PVHIN58-300 with TMHIN58-40Page 12XG0521 - 111214Installing the TMHIN58-40 TerminationTermination clearancesFigure 2 Section 5. Step 1. Unpackaging

PVHIN58-300 with TMHIN58-40Page 13XG0521 - 111214Step 2. If doing a concrete install, the termination has two adjustable mount-ing feet on the sides o

PVHIN58-300 with TMHIN58-40Page 14XG0521 - 111214Step 4. Vanity ring install.There is an optional vanity ring to cover the unnished edges of rock fac

PVHIN58-300 with TMHIN58-40Page 15XG0521 - 111214Figure 10 Section 5. vvFIXEDCLOSEDOPERABLEFCBvvOPERABLEFIXEDCLOSEDvBXBABJHIXKvMVBLDEVINSIDECORNER D

PVHIN58-300 with TMHIN58-40Page 16XG0521 - 111214Capacitor Replacement - REC 1257REC 1257 Note: Maintenance must be preformed by a qualied and certi

PVHIN58-300 with TMHIN58-40Page 17XG0521 - 111214Step 3. Cut zap strap securing wires together in bundle.Figure 6. Section 6 Step 4. Cut off large be

PVHIN58-300 with TMHIN58-40Page 18XG0521 - 111214Step 7. Strip about 3/8" to 1/2" off all wire that was cut.Figure 10. Section 6 Step 8. Tw

PVHIN58-300 with TMHIN58-40Page 19XG0521 - 111214Step 11. Reinstall component cover.Step 12. Reinstall blower cover. Step 13. Turn power back on and c

Page 2XG0521 - 111214Table of ContentsPVHIN58-300 with TMHIN58-40Instruction Manual ContentsSpecications � � � � � � � � � � � � � � � � � � � � � �

PVHIN58-300 with TMHIN58-40Page 20XG0521 - 111214Motor and Capacitor Replacement - REC 1258REC 1258 Note: Maintenance must be preformed by qualied pe

PVHIN58-300 with TMHIN58-40Page 21XG0521 - 111214Step 3. Unplug capacitor / blower assembly from power vent power cable.Step 6. Unscrew blower from po

PVHIN58-300 with TMHIN58-40Page 22XG0521 - 111214Step 8. Secure blower to Power Vent using supplied screws and star wash-ers. Make sure wire is close

PVHIN58-300 with TMHIN58-40Page 23XG0521 - 111214Step 13. Reinstall blower cover.Figure 16. Section 7 Step 11. Plug capacitor / blower assembly into P

PVHIN58-300 with TMHIN58-40Page 24XG0521 - 111214Appendix A: WarrantyThe WarrantyThe Companies warrants the Montigo Gas Appliance to be free from defe

PVHIN58-300 with TMHIN58-40Page 25XG0521 - 111214Appendix B: State of MassachusettsAmendment (Gas Fireplace / Equipment sold in the State of Massachus

XG0521 -111214PVHIN58-300 with TMHIN58-40

IntroductionPVHIN58-300 with TMHIN48-40Safety Alert KeyPage 3XG0521 - 111214SpecicationsGeneral InformationThis installation guide covers installatio

PVHIN58-300 with TMHIN58-40Page 4XG0521 - 111214Product Dimensions 8"202 8"202 2758"703 2078"532 23"584 2314"591 2

PVHIN58-300 with TMHIN58-40Page 5XG0521 - 111214Product Dimensions 14"354 3912"1003 3778"963 1238"316 8"2025"126 3658

PVHIN58-300 with TMHIN58-40Page 6XG0521 - 111214Installing the power ventFigure 1. Section 3 PVHIN58-300 ClearancesStep 1. Unpack the power vent from

PVHIN58-300 with TMHIN58-40Page 7XG0521 - 111214Step 3. Power vent cannot be installed closer than 7 feet of venting to the appliance. This is the cas

PVHIN58-300 with TMHIN58-40Page 8XG0521 - 111214Step 5. Remove two screws securing electrical plate.Step 6. Remove power vent cable from inside compon

PVHIN58-300 with TMHIN58-40Page 9XG0521 - 111214Step 8. Attach the power cable from the power vent to the control cable.Step 9. Push all excess cable