Montigo PVHFL58-300 Especificaciones

IF YOU SMELL GAS Do not try to light any appliance. Do not touch any electrical switch; do not use any phone in your building. Immediately call

ServicePage 10XG0519 - 070714Step 3: Remove the louver assembly by lifting the bottom end forward and then dropping the door out of the top latches. F

Step 1: Reinstall the rain guard using the supplied 3 screws. Figure 6.ServicePage 11XG0519 - 070714LouverAssemblyTabsScrewLocationsStep 3:1) Place Fr

ServicePage 12XG0519 - 070714Figure 7a.Figure 7b.PVHFL58-300 & PVHFL510-300 Horizontal Power VentServicingFrom the inside of the houseStep 1: Tur

Step 7: Remove the three screws securing the rain guard. Go to Capacitor or Motor and Capacitor Replacement Section. ServicePage 13XG0519 - 070714PVHF

ServicePage 14XG0519 - 070714Step 3: Secure inner can to the outer can with supplied 8 screws. Figure 8b.Figure 8c.Step 4: Plug control cable back i

ServicePage 15XG0519 - 070714PVHFL58-300 & PVHFL510-300 Horizontal Power VentCapacitor ReplacementREC 1250 Note: Maintenance must be preformed by

ServicePage 16XG0519 - 070714PVHFL58-300 & PVHFL510-300 Horizontal Power VentStep 6: Using the large bell connector, connect the black bre wire f

ServicePage 17XG0519 - 070714PVHFL58-300 & PVHFL510-300 Horizontal Power VentMotor and Capacitor ReplacementREC 1251 Note: Maintenance must be pre

ServicePage 18XG0519 - 070714PVHFL58-300 & PVHFL510-300 Horizontal Power VentStep 6: Unscrew 8 screws securing the motor mounting plate.Figure 10f

ServicePage 19XG0519 - 070714Go to reinstalling either from outside or inside. PVHFL58-300 & PVHFL510-300 Horizontal Power VentStep 13: Using the

IntroductionSpecicationsGeneral InformationThis installation guide covers installation of the External Power Vent System only. This system is designe

PVHFL58-300 & PVHFL510-300 Horizontal Power VentAppendix A: WarrantyThe WarrantyThe Companies warrants the Montigo Gas Appliance to be free from d

PVHFL58-300 & PVHFL510-300 Horizontal Power VentAppendix B: State of MassachusettsAmendment (Gas Fireplace / Equipment sold in the State of Massac

Ferndale, WashingtonTF: 1.800.789.6236FX: 1.866.3000.0927XG0519 - 070714Langley, British ColumbiaTF: 1.800.378.3115FX: 1.604.607.6462PVHFL58-300 &

Product DimensionsIntroductionFigure 1. PVHFL58-300 (Tolerance ± ⅛") [mm] Front ViewSide View 1834"476 2214"565 2118"538 1214&

Installing the power vent 1834"476 2214"565 FramingWall BoardOuter CanAssemblyFigure 2. Framing dimensionsInstallationStep 1: Unpack power

InstallationPage 5XG0519 - 070714Step 4: Slide the inner can out by pullingFigure 3c.Step 5: Screw outer can assembly into the wall 1834"476 221

InstallationPage 6XG0519 - 070714Step 8: Remove two screws securing electrical plate.Figure 3g.Step 9: Remove the power vent power cable from inside t

InstallationPage 7XG0519 - 070714LouverAssemblyTabsScrewLocationsStep 3:1) Place Front Grill into the Out Can Assembly by inserting top tabs into the

ServicePage 8XG0519 - 070714CPower Vent WiringBLUEBROWNBLACKWHITEBLACKGREEN6 PIN MOLEXCONNECTORKEY WAYPVHFL58-300 & PVHFL510-300 Horizontal Power

InstallationPage 9XG0519 - 070714Figure 4b.vvFIXEDCLOSEDOPERABLEFCBvvOPERABLEFIXEDCLOSEDvBXBABJHIXKvMVBLDEVINSIDECORNER DETAILvGAVVENTER TERMINALXAIR