search

Montigo MD38 DV2 Manual de usuario Pagina 8

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 22
  • Tabla de contenidos
  • MARCADORES
    • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 7
Page 8
MD38-DV-2 Homefire
Part No. XG0111
2' min.
Storm collar
Support ring
Roof flashing
30' max.
* Minimum 1" clearance to all combustibles
Support plate
Firestop
Installation
Installation Of Vertical Vent DV
n Vertical Terminations must be installed:
• minimum 2' (two feet) above the highest point where
vent passes through the roof.
• minimum 6' (six feet) from a mechanical air inlet
• minimum 18" (1 1/2 feet) from a parapet wall.
n Maximum vent height is 35 feet above fireplace.
Note: Flame characteristics will change if the maximum vent
height is used.
n Minimum clearances 1" from vent to all combustible materials
must be maintained.
Figure 13. Straight, vertical venting using required MXT-10 adaptor.
n A maximum of two offsets (each offset has two 90° bends) may be
made and shall not exceed total length of 25% of the vertical vent height,
when measured center to center of piping.
Example: Typical vent installation.
20' vertical vent
2 - 2' offsets required
25% of 20' = 5' max. offset allowed
This venting configuration meets requirements.
A - Termination MVTK-1
B - Flex sections MFL-1 (12" section)
MFL-2 (24" section)
MFL-3 (36" section)
MFL-4 (48" section)
C - Solid sections MEXT-1 (12" section)
MEXT-2 (24" section)
MEXT-3 (36" section)
MEXT-4 (48" section)
D - Support Ring & Plate MSPXT-8 (7" dia.)
E - Firestop FS-7 (7" dia.)
F - Roof Flashing MRF-7 (1/12 - 7/12 pitch)
MRF-12 (7/12 - 12/12 pt.)
MRF-16 (12/12 - 16/12 pt.)
Figure 14b. Vertical venting with 2 offsets (1 offset= two 90° bends).
Figure 14a. Vertical venting with 1 offset (1 offset= two 90° bends).
2' min.
2'
Storm collar
Roof flashing
30' max.
* Minimum 1" clearance to all combustibles
Support straps or
support plate & ring
Firestop
Firestop
Firestop
Support plate
& ring
35' max.
35' max.
Top Vent
Storm collar
Support ring
MEXT
Solid Section
Roof flashing
30' max.
* Minimum 1" clearance to all combustibles
Support plate
Firestop
Firestop
2' min.
MXT-10
Adaptor
MEXT
Flue
Collar
35' max.
Vista de pagina 7
1 2 3 4 5 6 7 8 9 10 11 12 13 ... 21 22

Comentarios a estos manuales

Sin comentarios
Relacionado con productos y manuales para Para Casa Montigo MD38 DV2
Para Casa Montigo MD44 DV Manual de usuario   (20 paginas)
Para Casa Montigo ME34DV Manual de usuario   (20 paginas)
Para Casa Montigo ME34-DV2 Manual de usuario   (20 paginas)
Para Casa Montigo ME38 ODV Manual de usuario   (18 paginas)
Para Casa Montigo ME34 BV Manual de usuario   (14 paginas)
Para Casa Montigo MW34 DV Manual de usuario   (22 paginas)
Para Casa Montigo MW38 BV Manual de usuario   (14 paginas)
Para Casa Montigo SP28 F2 Manual de usuario   (16 paginas)
Para Casa Montigo MW38 DV Manual de usuario   (21 paginas)
Para Casa Montigo 34DVI Tuscany Manual de usuario   (20 paginas)
  • Uniplex Active Key WeatherBug Roketa Vxl
  • I-rocks No GE Proyectores de datos Hitachi Proyectores ASROCK Placas base Kawasaki Accesorios de motos
  • Casio CTK-3400 Yamaha DXS Series Philips AZ1826/12 Samsung SC-X210L Sony DSC-S2100
  • Nokia 6610 Manual de usuario Epson WF-7110 Guía de usuario Jvc GR-D860 Manual de usuario LG HT356SD Manual de usuario LG RT-21FD15V Manual de usuario